Last Modified: 11-29-2007 1.6 A
Service Category: Drivetrain Section: Automatic Transmission/Transaxle
Model Year: 2008 Model: Sequoia Doc ID: RM000003F6T000X
Title: A750E AUTOMATIC TRANSMISSION / TRANSAXLE: OIL COOLER: INSTALLATION (2008 Sequoia)

INSTALLATION

1. INSTALL TRANSMISSION OIL COOLER ASSEMBLY (w/o Trailer Towing System)

(a) Coat 2 new O-rings with ATF, and install them to the transmission oil cooler.

(b) Align the transmission oil cooler with the transmission oil cooler spacer and assemble them with the 3 bolts.

Torque: 8.0 N·m (82 kgf·cm, 71 in·lbf)

(c) Connect the 2 transmission oil cooler hoses to the transmission oil cooler spacer with the 2 clips.

(d) Temporarily install the transmission oil cooler with transmission oil cooler spacer with bolt A.

(e) Install the bolt B and tighten it to the specified torque. Then tighten bolt A to the specified torque.

Torque: 21 N·m (214 kgf·cm, 16 ft·lbf)

(f) Connect the 2 transmission oil cooler hoses with the 2 clips.

HINT:

Make sure the pinching portion of each clip is facing the direction shown in the illustration.

2. INSTALL TRANSMISSION OIL COOLER ASSEMBLY (w/ Trailer Towing System)

(a) Coat 2 new O-rings with ATF, and install them to the transmission oil cooler.

(b) Align the transmission oil cooler with transmission oil thermostat and assemble them with the 3 bolts.

Torque: 8.0 N·m (82 kgf·cm, 71 in·lbf)

(c) Connect the 2 transmission oil cooler hoses to the transmission oil thermostat with 2 clips.

(d) Temporarily install the transmission oil cooler with transmission oil thermostat with bolt A.

(e) Install the bolt B and tighten it to the specified torque. Then tighten bolt A to the specified torque.

Torque: 21 N·m (214 kgf·cm, 16 ft·lbf)

(f) Connect the 2 transmission oil cooler hoses with the 2 clips.

HINT:

Make sure the pinching portion of each clip is facing the direction shown in the illustration.

(g) Connect the 2 No. 2 transmission oil cooler hoses to the transmission oil thermostat.

3. CONNECT WATER BY-PASS PIPE ASSEMBLY

(a) Connect the 2 water by-pass hoses with the 2 clips and install the water by-pass pipe with the bolt.

Torque: 18 N·m (184 kgf·cm, 13 ft·lbf)

HINT:

Make sure the pinching portion of each clip is facing the direction shown in the illustration.

4. INSTALL HOSE HEAT PROTECTOR

(a) Install the hose heat protector with the bolt.

Torque: 21 N·m (214 kgf·cm, 16 ft·lbf)

5. INSTALL FRONT EXHAUST PIPE ASSEMBLY 2UZ-FE INTAKE / EXHAUST: EXHAUST PIPE: INSTALLATION (2008 Sequoia)+

6. ADD ENGINE COOLANT 2UZ-FE COOLING: COOLANT: REPLACEMENT (2008 Sequoia)+

7. ADJUST AUTOMATIC TRANSMISSION FLUID

(a) Adjust automatic transmission fluid A750E AUTOMATIC TRANSMISSION / TRANSAXLE: AUTOMATIC TRANSMISSION FLUID: ADJUSTMENT (2008 Sequoia) .

8. INSPECT FOR AUTOMATIC TRANSMISSION FLUID LEAK

9. INSPECT FOR ENGINE COOLANT LEAK 2UZ-FE COOLING: COOLING SYSTEM: ON-VEHICLE INSPECTION (2008 Sequoia)+

10. INSPECT FOR EXHAUST GAS LEAK